Waeco SP-900 Installation Manual

DE 11 LKW-SplitklimaanlageEinbauanleitungEN 30 HGV split air conditionerInstallation manualFR 49 Climatiseur split pour poids lourdsNotice de montageE

Safety instructionsCoolAir30Contents1 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31Safety instructionsCoolAir1.1 Using the device Only use the air conditioner for the purpose specified by the manufacturer and do not make any alter

Conventions in this manualCoolAir322 Conventions in this manual2.1 General information on the installation manualThis installation manual contains th

33Proper useCoolAiraThe safety instruction indicates potential hazards which could arise during the installation or operation of the product and caus

Scope of deliveryCoolAir344 Scope of deliveryCoolAir SP-9005InstallationaCautionThe air conditioner may only be installed by qualified personnel from

35InstallationCoolAir5.2 Notes on installationeWarningMake sure that all electrical components are electrically discharged before carrying out work on

InstallationCoolAir365.3 Installation stepsaCautionThe manufacturer only assumes liability for parts included in the scope of delivery. The validity o

37InstallationCoolAir5.3.2 Installing the condenser unitITo install the condenser unit using a vehicle-specific WAECO fastening frame, please observe

InstallationCoolAir385.3.3 Installing the evaporator unitThe evaporator unit is fitted on the vertical rear panel, near the bunk, in a horizontal posi

39InstallationCoolAir5.3.4 Connecting the condenser unit to the evaporator unitaCautionAvoid narrow radii during bending. Use a suitable round object

3CoolAir11232SP-900-Install.book Seite 3 Montag, 25. Januar 2010 4:53 16

InstallationCoolAir40IThe connection lines should be installed at right angles to the rear panel of the lorry (see Fig. 12 on page 7). For this purp

41InstallationCoolAir5.3.5 Installing and connecting the power cableIWe recommend that you connect the power cable to the fuse box or terminal block i

InstallationCoolAir42ICheck the voltage drop between the vehicle connection and the cable connector on the compressor. The voltage drop must not excee

43ConfigurationCoolAir6 ConfigurationBefore you first start up the system, you can adapt the controls according to the installation conditions. This m

ConfigurationCoolAir446.2 Menu level 1: Set temperatureThe system always starts with a defined value for the room temperature. This parameter can be c

45ConfigurationCoolAir➤ Use the Temp. + and - buttons (fig. 184 or 5) to select the low voltage cut-off value. The characteristic figures at second an

ConfigurationCoolAir466.5 Menu level 4: Default settingYou can reset the parameters you set in configuration mode at menu levels 1 to 3 to the default

47Maintenance and careCoolAir7 Maintenance and careaCautionDo not use abrasive cleaning agents or hard objects during cleaning as these can damage the

Technical dataCoolAir488 Technical dataVersions, technical modifications and delivery options reserved.CoolAir SP-900 air conditioner Item number 910

Europe Dometic Austria GmbHNeudorferstrasse 1082353 Guntramsdorf℡ +43 2236 908070 +43 2236 90807060Mail: [email protected] Switzerland AGRiedacker

CoolAir434SP-900-Install.book Seite 4 Montag, 25. Januar 2010 4:53 16

5CoolAir567SP-900-Install.book Seite 5 Montag, 25. Januar 2010 4:53 16

CoolAir68910SP-900-Install.book Seite 6 Montag, 25. Januar 2010 4:53 16

7CoolAir111213SP-900-Install.book Seite 7 Montag, 25. Januar 2010 4:53 16

CoolAir814SP-900-Install.book Seite 8 Montag, 25. Januar 2010 4:53 16

9CoolAirC+TF-C+F++1234wbrgrgl-wbrglgr444130010844413001084441300097444130009744413000964441300096swro+-swroroglblrobrbrro+-15bl br gl gr ro sw wDE Bla

CoolAir10161718156234897SP-900-Install.book Seite 10 Montag, 25. Januar 2010 4:53 16